(0) (3) (10) Water Tankers for
Capacity 9250
US Gallons with 75 gal overage
Compartments Single
Shape Round
straight bore with 2 ½” pitch to rear
Products Various
Maximum Product Weight 12 pound per gallon
Product Temperature 190°F maximum temperature
Code None
Working Pressure 25
PSI with 40 PSI test
Tank Shell & Finish 10
gauge 304-2B stainless steel
Tank Head 10
gauge 304-2B stainless steel ASME type flanged & dished head
Inside Weld Finish All
inside welds ground snag free with l2” wide section on bottom ground
flush for drainage
Baffles (2)
10 gauge full baffles with drain at bottom, vent at top, & 20”
diameter reinforced walk-through opening at center located equally spaced
between manhole & heads
Heat Section None
Manhole 20”
diameter 304 stainless steel full opening Chemical type manhole with 6 hold
downs, white Hypalon gasket & hinge pin at
front located at center of tank
Clean Outs None
Vents 3”
Fort Vale DOT-407 pressure - vacuum vent set t 30 PSI with ¾” ball
valve air inlet & 0-60 PSI pressure gauge located in manhole cover
Rings
304 stainless fully welded to inner tank
Bolsters 10
gauge 304 stainless steel
Frame 304
stainless sub frame
Insulation 6”
thick fiberglass compressed to 5”
Saddle Sheet Stainless
Steel
Outer Jacket 22
gauge stainless steel bright anneal finish with lapped seams
Outer Heads 18
gauge stainless steel bright anneal finish with lock seam joints
Spill Dam Stainless
steel spill dam
Spill Dam Hose Two
1 ½”diameter Tigerflex drain hoses
located one per side
Roll Over None
Wrapper Top Back-up Aluminum
hard top full length of tank
Wrapper lap back up Polyurethane
foam with max 300° F
Walkway 12”
wide aluminum grip strut at curb side of spill dam
Ladder One
16” wide stainless steel ladder located on curbside of manhole with
channel rung, top platform step and safety side rails
Fenders Aluminum
on front & rear with stainless supports
Rear Light Box Stainless
steel bolt on
Lights & Wiring Truck-Lite lights with wire harness system & center
directional lights with wiring in 1 ½” stainless tube from front
head to front of running gear
Connector 7
way receptacle on stainless bracket with glad hands located below centerline of
front head
Mud Flaps Heavy-duty
anti-sail plain black at front & rear with stainless supports
Bumper 4”
x 4” stainless steel under ride guard
Tire Carrier None
Landing Gear 2
speed, heavy-duty Jost leg with sand shoes with crank
on curbside & stainless steel frame
Upper Fifth Wheel Heavy-duty
bolted adjustable plate
Hose Carrier Two
6” diameter x 21’ long aluminum hose tubes with cast doors on both
ends mounted one per side with stainless supports
Suspension Hutch
Model 9700 cast equalizer with 8 leaf Springs and stainless steel frame
Axles 5”
round Rockwell TP-4671-Q axle with TP spindle x 71.5” track
Brakes 16
l/2 x 7 non-asbestos S-Cam air & Haldex auto
slacks
Wheels 10
stud hub pilot unimount cast hub with outboard cast
drum
Wheel Seals Stemco oil seal
Anti-skid Spring
brakes & equipment to meet l2l standards with Rockwell WABCO 4S/2M
anti-skid
Hubdometer None
Rims 22.5
x 8.25 10 hole Unimount steel painted white
Tires 11R
22.5 x 16 ply Goodyear G-149
Government Seals On
all openings
Emergency Valve None
Emergency Valve Oper None
Outlet Valve 6”
Betts Lever Knife outlet valve
Valve Gaskets Teflon
Envelope
Outlet Fitting None
6” Stainless steel MPT on valve outlet
Piping 6”
Stainless steel flanged outlet tube straight out rear head
Thermometer None
Outside Weld Finish All
outside welds discoloration removed
Calibration Theoretical
in l” increments
Paint Prime
and Paint all mild steel parts black - DO NOT PAINT STAINLESS STEEL
Tractor 48“
Fifth Wheel
Weight Laws Federal
Weight Laws
Flip Signs None
Front Unloading Line None
Front Air Unloading Line None
Conspicuity Strips Red
& White strips on both sides & rear
Registration Holder Betts
PS-1 at curbside landing gear frame